Install the radiator of the high-temperature coolant circuit
Further information is available.
NOTE:
TECHNICAL INFORMATION
Notes on work at the cooling system form the basis of these repair instructions and must be complied with at all times.
For additional information see: 17 00... INSTRUCTIONS FOR REPAIR WORK ON COOLING SYSTEM
Notes on work at the cooling system form the basis of these repair instructions and must be complied with at all times.
For additional information see: 17 00... INSTRUCTIONS FOR REPAIR WORK ON COOLING SYSTEM
NOTE:
TECHNICAL INFORMATION
Make sure that the connections are locked correctly. The locks must engage audibly.
Make sure that the connections are locked correctly. The locks must engage audibly.
- Guide in radiator of low-temperature coolant circuit (1) with radiator of high-temperature coolant circuit (2) and install.
- Tighten screw (1) bottom cooling module, left.
TIGHTENING TORQUES SPECIFICATION
| Radiator to cooling module, bottom | ||
| TS6x20 | Tightening torque | 6 Nm |
- Tighten screw (1) bottom cooling module, right.
TIGHTENING TORQUES SPECIFICATION
| Radiator to cooling module, bottom | ||
| TS6x20 | Tightening torque | 6 Nm |
- Guide in the cover (3) of the cooling module at the bottom left and install.
- Ensure that the locking mechanism (2) engages audibly.
- Ensure that the lock (1) engages audibly.
- Ensure that the locking mechanisms (1) engage audibly.
- Feed in and install cover (3) on cooling module, bottom right.
- Ensure that the locking mechanism (2) engages audibly.
- Ensure that the locking mechanism (1) engages audibly.
- Connect and lock coolant line (1).
- Make sure that the cooling line (1) engages audibly.
- Feed in air duct (2) in direction of arrow and install.
- Secure clamps (1).
- Guide in and install cover (2), front right.
- Secure clamps.
- Tighten down screws (1).
TIGHTENING TORQUES SPECIFICATION
| Cover to front bumper | ||
| screw | Tightening torque | 3 Nm |
- Thread in air duct (1) and install.
- Tighten the screws (arrows).
TIGHTENING TORQUES SPECIFICATION
| Cover to front bumper | ||
| screw | Tightening torque | 3 Nm |
- Connect and lock coolant line (1).
- Make sure that the coolant line (1) engages audibly.
- Connect and lock coolant line (1).
- Make sure that the coolant line (1) engages audibly.
- Connect and lock coolant line (2).
- Connect and lock coolant line (1).
- Make sure that all coolant lines engage audibly.
- Connect and lock transmission oil line (3).
- Make sure that transmission oil line (3) engages audibly.
- Feed in and install transmission oil lines (3).
- Insert and install the holder (2).
- Tighten down screw (1).
TIGHTENING TORQUES SPECIFICATION
| Transmission oil lines to front axle support holder | ||
| TS6X20 | Tightening torque | 4 Nm |
- Feed in and install the cover (3) in the cooling module above.
- Ensure that the locking mechanisms (2) engage audibly.
- Ensure that the locks (1) engage audibly.
Follow-up works
- Refer to INSTALL FAN COWL .
- Refer to INSTALL THE REAR TOP CROSS CONNECTION .
- Refer to INSTALL FRONT CROSS CONNECTION .
- Refer to INSTALLING FRONT-END STRUT ON LEFT AND RIGHT .
- Refer to INSTALLING THE COVER ON THE LEFT AND RIGHT IN THE ENGINE COMPARTMENT AT THE TOP
- Refer to INSTALL RESONATOR .
- Refer to FILL AND VENT THE HIGH-TEMPERATURE COOLANT CIRCUIT .
- Refer to FILL AND VENT THE LOW-TEMPERATURE COOLANT CIRCUIT .
- Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- Refer to INSTALL THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .