Install Engine Mount In Front Of Cowling With Wheel Arch

Further information is available.

Pre-clean bonding surfaces on vehicle and on new part with cleaning agent R2.
CONSUMABLE - CLEANING AGENT DESCRIPTION (R2)

Cleaning agent R2 500 ml 83190417324
Clean bonding surfaces on vehicle and on new part with cleaning agent R1.
CONSUMABLE - CLEANING AGENT DESCRIPTION (R1)

Cleaning agent R1 100 ml, Bottle 83192211217
Apply adhesive K1 to the bonding surfaces.
ADHESIVE DESCRIPTION

Body adhesive K1 195 ml 83190413015
Install the new parts with an alignment bracket or a universal mount.
Rivet new parts in the areas (1), (2) and (4) with blind rivets N1.
CONSUMABLE - BLIND RIVET DESCRIPTION (N1)

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414
In the area (3), use a bind rivet N2.
CONSUMABLE - BLIND RIVET DESCRIPTION (N2)

Blind rivet N2
Ø 6.5 mm; clamping area 4.8-6.8 mm 83190301419

Courtesy of BMW OF NORTH AMERICA, INC.
Weld reinforcement (1) in the area (2).
In the (3), MAG weld analogue to the series.

Courtesy of BMW OF NORTH AMERICA, INC.
Weld reinforcement (1) in the area (2).
Avoid excessive application of heat in this process.

The cowling cross-member (3) is filled with hardly inflammable cavity foam.
In case of smoke formation: Stop the welding procedure and cool the welded area with compressed air if applicable.

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet new parts in the areas (1) with blind rivets N1.
CONSUMABLE - BLIND RIVET DESCRIPTION (N1)

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
For additional information see: 41 00... Installation of a cavity sealing (not expanding)

Apply sealant D1 to the new cavity sealing (1).
CONSUMABLE - SEALANT DESCRIPTION

Sealant D1 (seam sealing) 310 ml 83422409985

Courtesy of BMW OF NORTH AMERICA, INC.
Install cavity sealing (1) in the new part.
Apply sealant D1 to cavity sealing (1).
Install the carrier support for the new part.
Rivet the new parts in the areas (1) and (2) with blind rivets N1.
CONSUMABLE - BLIND RIVET DESCRIPTION

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414
Rivet the new parts in the areas (3) with blind rivets N3.

Courtesy of BMW OF NORTH AMERICA, INC.

CONSUMABLE - BLIND RIVET DESCRIPTION (N3)

Blind rivet N3
Ø 4 mm; clamping area 1-3 mm 83190301421
In the area (4), use a bind rivet N6.
CONSUMABLE - BLIND RIVET DESCRIPTION (N6)

Blind rivet N6
Ø 4 mm; clamping area 3-5 mm 83192158655
Weld the new parts in areas (1) according to the new part preparation process.
Avoid excessive application of heat to adhesive areas.

Courtesy of BMW OF NORTH AMERICA, INC.
Weld the new part in areas (1) according to the new part preparation process.
Avoid excessive application of heat to adhesive areas.

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet new parts in the areas (1) and (2) with blind rivets N1.
CONSUMABLE - BLIND RIVET DESCRIPTION

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.
Rivet the new part in the areas (1) with blind rivet N1.
CONSUMABLE - BLIND RIVET DESCRIPTION

Blind rivet N1
Ø 6.5 mm; clamping area 2.8-4.8 mm 83190301414

Courtesy of BMW OF NORTH AMERICA, INC.

Installing the EMC screw
Drill the hole with a diameter of 4.2 mm after the adhesive completely hardens.
Screw in the EMC screw.
Seal the EMC screw with the sealant.
CONSUMABLE - SEALANT DESCRIPTION

Sealant D1 (seam sealing) 310ml 83422409985
Install two EMC screws in the areas (1).
CONSUMABLE - SCREW DESCRIPTION

screw
EMC screw, SF Plus, M5x15 83190301639

Courtesy of BMW OF NORTH AMERICA, INC.
Install an EMC screw in area (1).
CONSUMABLE - SCREW DESCRIPTION

screw
EMC screw, SF Plus, M5x15 83190301639

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to CUT THE THREADS .
Refer to ACTIVATE HIGH-VOLTAGE SYSTEM .
Refer to INSTALL FLAP IN RIGHT LUGGAGE COMPARTMENT TRIM PANEL .