GEAR OIL, DRAINING AND FILLING, 0B0, 09R "quattro ultra"

Special tools and workshop equipment required 

• Charging Device for AWD Clutch Coupling 2: VAS 6291A 
  Fig 1: Device For Haldex Coupling 2 - Adapter 2VAS6291/2

  Courtesy of AUDI OF AMERICA, LLC
• Adapter for Oil Filling: VAS 6291/1  or Charging Device for AWD Clutch Coupling 2 - Adapter 2 : VAS 6291/2 
• Charging Device For AWD Clutch Coupling 2 - Adapter 3: VAS 6291/3  (rework if necessary. Refer to Fig 5.)
  Fig 2: Identifying Charging Device For Haldex Coupling 2 - Adapter 3 VAS6291/3

  Courtesy of AUDI OF AMERICA, LLC
• The Oil Filler - Adapter 6: VAS 6262/6  must be used on some fluid containers.
  Fig 3: Adapter For Oil Filling 6 VAS 6262/6

  Courtesy of AUDI OF AMERICA, LLC
• The Oil Filler - Adapter 7: VAS 6262/7  must be used on some fluid containers.
  Fig 4: Identifying Adapter

  Courtesy of AUDI OF AMERICA, LLC
• Drip Tray

Depending on the version, the spacer tube from the Charging Device For AWD Clutch Coupling 2 - Adapter 3VAS 6291/3 can line up on the housing rib on the final drive.

-- Grind the adapter spacer tube as shown, opposite both the side holes -arrows-.

Draining 

-- Final drive 0B0: remove the gear oil check plug -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Final drive 09R: remove the gear oil check plug -1-.

Courtesy of AUDI OF AMERICA, LLC

• Removing the gear oil check plug allows the gear oil to drain faster.

-- Remove the drain plug -2- and drain the gear oil.

-- Then tighten the gear oil drain plug -2-.

• Tightening specification: Refer to COMPONENT LOCATION OVERVIEW - DRAIN AND CHECK PLUGS .

Filling

-- Final drive 0B0: remove the gear oil check plug -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Final drive 09R: remove the gear oil check plug -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Install the Adapter for Oil Filling: VAS 6291/1  or Charging Device for AWD Clutch Coupling 2 - Adapter 2 : VAS 6291/2  -1-.

-- Attach the elbow -A- to the adapter -B-.

-- Route the hose over the right drive axle.

• The hose must not sag. It must be routed over the right rear wheel.

-- Lower the vehicle.

-- Make sure that the valve -arrow- is closed.

-- Screw the fluid container -A- onto the Charging Device for AWD Clutch Coupling 2: VAS 6291A  .

-- Open the valve -arrow- and hold the oil container as shown.

The rear final drive will not be filled.

• When at the correct filling of the rear final drive oil drips between the adapter -B- and the final drive housing.
  Fig 9: Identifying Elbow With Adapter

  Courtesy of AUDI OF AMERICA, LLC

-- Lift the vehicle.

-- If oil leaks from the adapter -B-, set down the oil container (for example, on a tool trolley).

A portion of the excess oil runs back into the oil container.

-- If no more oil runs back, remove the Charging Device for AWD Clutch Coupling 2: VAS 6291A  .

• The oil level is correct when the rear final drive is filled up to the lower edge of the oil fill hole.

-- Then tighten the gear oil check plug.

• Tightening specification: Refer to COMPONENT LOCATION OVERVIEW - DRAIN AND CHECK PLUGS .