Installing the engine wiring harness for sensor system 2
Engine wiring harness for sensor system 2
- Engine wiring harness for sensor system 2
NOTE:
RISK OF DAMAGE
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
Improper routing of cables and wiring harnesses.
Trapped, crushed or damaged cables may cause short circuits and malfunctions.
- Route all cables without abrasions, do not trap and crush.
- Guide in and install the engine wiring harness (1) for sensor system 2.
- Feed in and install the wiring harness section (5) for sensor system 2.
- Connect connectors (4) and lock.
The connector (4) must engage audibly.
- Install and lock the locking mechanisms (3).
- Secure the clamps (arrows).
- Connect connectors (2) and lock.
The connectors (2) must engage audibly.
- Connect connectors (1) and lock.
The connectors (1) must engage audibly.
- Guide in connector (2) in direction of arrow to the carrier plate (3) and install.
- Ensure that the locking mechanisms (1) engage correctly.
- Secure cable (4) to the clamp (5).
- Connect connectors (1) and lock.
- Make sure the connector (1) engages audibly.
- Connect the connector (1) with the holder (2) and lock (arrow).
The connector (1) must engage audibly.
- Connect connectors (1) and lock.
The connector (1) must engage audibly.
- Guide in and install the engine wiring harness (2) for sensor system 2.
- Secure the clamps (arrows).
- Connect connectors (1) and lock.
The connectors (1) must engage audibly
- Guide in the wiring harness section (2) and install.
- Secure clamps (arrow).
- Connect connectors (1) and lock.
The connector (1) must engage audibly.
- Feed in and install the wiring harness section (4) for sensor system 2.
- Ensure that the locking mechanisms (arrows) engage correctly.
- Thread in ground cable (3) and install.
- Tighten nut (2).
TIGHTENING TORQUES SPECIFICATION
| Standard screw connection M6 | ||
|---|---|---|
| M6 | Tightening torque | 8 Nm |
- Connect connectors (1) and lock.
The connectors (1) must engage audibly.
- Insert the bracket (3) in the direction of the arrow and install.
- Make sure the locking mechanism (2) engages audibly.
- Fasten the cable bracket (1) to the bracket (3).
- Insert and install the coolant hose (5).
- Lock holder (4).
- Feed in the wiring harness section (3) on the brackets (arrows) and fasten.
- Insert and install the tank vent line (2).
- Tighten down screw (1).
TIGHTENING TORQUES SPECIFICATION
| Tank vent line to intake plenum | ||
|---|---|---|
| Oval-head screw | Tightening torque | 3 Nm |
- Connect connectors (1) and lock.
The connector (1) must engage audibly.
- Attach the connector (2) to the holder (3) and lock.
The connector (2) must engage audibly.
- Connect connectors (1) and lock.
The connector (1) must engage audibly.
- Connect connectors (1) and lock.
The connectors (1) must engage audibly.
Follow-up work
- Refer to INSTALLING COVER FOR THE DME CONTROL UNIT .
- Refer to INSTALLING THE CYLINDER HEAD COVER ACOUSTIC COVER .
- Refer to INSTALLING DIFFERENTIAL PRESSURE SENSOR .
- Refer to INSTALLING ENGINE VENTILATION LINE .
- Refer to INSTALLING RESONATOR .
- Refer to INSTALLING ACOUSTIC COVER AT REAR .
- Refer to INSTALLING ACOUSTIC COVER .
- Refer to INSTALLING THE CENTER COWL UPPER PART .
- Refer to INSTALLING TENSION STRUT ON SHOCK TOWER .
- Refer to INSTALLING WINDSHIELD PANEL COVER .
- Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
- Refer to INSTALLING THE REAR RIGHT ENGINE COMPARTMENT COVER .
- Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
- Refer to INSTALLING THE FRONT HOOD SEAL AT THE REAR .
- Refer to CONNECTING NEGATIVE BATTERY CABLE .