Installing the complete exhaust system

CAUTION: Component with heavy weight.
Injury hazard!

Note component's center of gravity.
Support component using a jack.
Secure component against falling off the jack.

CAUTION: Heavy component.
Heavy components can lead to injury or damage.

Remove and install heavy components with the aid of another person/other persons.

CAUTION: Grinding dust from grinding of components.
Hazardous to health!

Directly draw off the grinding dust.
Ensure adequate ventilation.
Conduct all work in appropriate personal protective equipment only.

NOTE: TECHNICAL INFORMATION
Check the exhaust system for tightness after installation.

NOTE: TECHNICAL INFORMATION
Mount the exhaust system in a de-energized state, following the tightening sequence from the rear silencer towards the exhaust manifold.

CAUTION: Shavings resulting from sawing or grinding components.
Injury hazard!

Conduct all work in appropriate personal protective equipment only.
Wear safety goggles and hand protection.

Courtesy of BMW OF NORTH AMERICA, INC.

Version with ribbon clamp:
Open the weld seam (1) with a conventional tool.
Remove ribbon clamp (2).
Replace the (2) ribbon clamp.
Parts: Ribbon cable clamp

NOTE: Schematic diagram is for example purposes. Some parts may differ in certain details.
Check all rubber mounts (1) of the exhaust system for damage and replace, if necessary.

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: TECHNICAL INFORMATION
Conduct the following operation with the assistance of a second person.
Insert and install the exhaust system with the help of another person.
Replace nuts (1).
Parts: Nuts

Tighten nuts (1).

Courtesy of BMW OF NORTH AMERICA, INC.

TIGHTENING TORQUES SPECIFICATION

Rear silencer to body/bumper support
M8 Replace nuts.	Tightening torque	19 Nm
M8 Replace nuts.	Tightening torque	19 Nm

Replace nuts (2).
Parts: Nuts

Tighten nuts (2).

TIGHTENING TORQUES SPECIFICATION

Rear silencer to body/bumper support
M8 Replace nuts.	Tightening torque	19 Nm
M8 Replace nuts.	Tightening torque	19 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Connect and lock the connector (1).

The connector (1) must engage audibly.

NOTE: The following step(s) must be performed if the listed component(s) is/are installed.

Replace the screw (1).
Parts: Screw
Tighten the bolt (1) on the rear axle support.

TIGHTENING TORQUES SPECIFICATION

Exhaust system to rear axle carrier
M8x25 Replace screw.	Tightening torque	28 Nm
M8x25 Replace screw.	Tightening torque	28 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: The following step(s) must be performed if the listed component(s) is/are installed.

Replace the screw (3).
Parts: Screw
Tighten the screw (3) on the rear axle support.

Courtesy of BMW OF NORTH AMERICA, INC.

TIGHTENING TORQUES SPECIFICATION

Exhaust system to rear axle carrier
M8x25 Replace screw.	Tightening torque	28 Nm
M8x25 Replace screw.	Tightening torque	28 Nm

Mount the ground strap (2) and tighten the screw (1).
Replace nut (1).
Parts: Nut
Tighten nut (1).

Courtesy of BMW OF NORTH AMERICA, INC.

TIGHTENING TORQUES SPECIFICATION

Front pipe/front silencer/gasoline particulate filter to the transmission holder
M8 Replace nut.	Tightening torque	19 Nm
M8 Replace nut.	Tightening torque	19 Nm

Tighten the ribbon clamp (1).

TIGHTENING TORQUES SPECIFICATION

Exhaust system to catalytic converter
Ribbon clamp nut M8 Replace the ribbon clamp.	Tightening torque	26 Nm


Ribbon clamp nut M10 Replace the ribbon clamp.	Tightening torque	55 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Version with V ribbon clip:
Replace V-band clamp.

Parts: V-band clamp

Unscrew the nut (1) and remove the sealing ring (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Bend all sheet metal tabs around their entire perimeter (apart from those in the marked areas) with a suitable tool.

Courtesy of BMW OF NORTH AMERICA, INC.
Mount the V-clip (1) on the sealing ring (2).
Make sure that the V-ribbon clip is (1) correctly positioned on the sealing ring (2).

Courtesy of BMW OF NORTH AMERICA, INC.
Make sure that, after mounting, the V-ribbon clip is on the sheet metal tabs in the marked areas.

Courtesy of BMW OF NORTH AMERICA, INC.
Connect the exhaust system (1) with the catalytic converter (2) and position it correctly (arrow).

Courtesy of BMW OF NORTH AMERICA, INC.
Make sure that V-clip (1) is fitted correctly.
Tighten down screw (2).

TIGHTENING TORQUES SPECIFICATION

V-ribbon clip
Replace V-ribbon clip. V-ribbon clip to catalytic converter	Tightening torque	25 Nm
Replace V-ribbon clip. V-ribbon clip to catalytic converter	Tightening torque	25 Nm

Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up work

Refer to IF INSTALLED: INSTALL THE TORSION STRUT ON THE RIGHT, AND ON THE LEFT WHERE REQUIRED .
Refer to INSTALL THE CONNECTING SUPPORTS ON THE TUNNEL .