Install lower heat shield
- Install heat shield (2).
- Secure screws (1).
TIGHTENING TORQUES SPECIFICATION
| Standard screw connection M6 | ||
|---|---|---|
| M6 | Tightening torque | 8 Nm |
Follow-up work
- Refer to INSTALLING THE EXHAUST MANIFOLD ON THE LEFT AND RIGHT .
- Refer to INSTALLING THE FRONT HEAT PROTECTION .
- Refer to FASTENING THE SCREW ON THE HEAT SHIELD ON THE FRONT RIGHT .
- Refer to FASTENING THE SCREW TO THE HEAT SHIELD AT THE FRONT LEFT .
- Refer to REPLACING THE SEAL FOR THE EXHAUST GAS TURBOCHARGER .
- Refer to REPLACING THE OIL RETURN LINE .
- Refer to INSTALLING EXHAUST TURBOCHARGER FOR CYLINDER 1 TO 4 .
- Refer to REPLACING THE OIL RETURN LINE .
- Refer to INSERT THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 5 TO 8 .
- Refer to ATTACHING THE OIL SUPPLY LINE ON THE EXHAUST TURBOCHARGER OF CYLINDERS 1 TO 4 .
- Tighten down screw (1).TIGHTENING TORQUES SPECIFICATION
Oil feed line to exhaust turbocharger M6x16 Tightening torque 10 Nm - Refer to SECURING OIL FEED LINE ON EXHAUST TURBOCHARGER OF CYLINDERS 5 TO 8 .
- Tighten down screw (1).TIGHTENING TORQUES SPECIFICATION
Oil feed line to exhaust turbocharger M6x16 Tightening torque 10 Nm - Refer to FASTENING THE BANJO BOLT FOR THE COOLANT RETURN LINE ON THE EXHAUST TURBOCHARGER OF THE CYLINDERS 1 TO 4 .
- Refer to FASTENING THE COOLANT FEED LINE AT THE EXHAUST TURBOCHARGER FOR THE CYLINDERS 1 TO 4 .
- Refer to FASTENING THE BANJO BOLT FOR THE COOLANT FEED LINE TO THE EXHAUST TURBOCHARGER OF THE CYLINDERS 1 TO 4 .
- Refer to INSTALLING THE COOLANT FEED LINE ON THE EXHAUST TURBOCHARGER FOR CYLINDERS 5 TO 8 .
- Refer to SECURING BANJO BOLT OF COOLANT RETURNING LINE ON EXHAUST TURBOCHARGER FOR CYLINDERS 5 TO 8
- Refer to FASTENING THE BANJO BOLT FOR THE COOLANT FEED LINE TO THE EXHAUST TURBOCHARGER OF THE CYLINDERS 1 TO 4 .
- Refer to SECURING THE BANJO BOLT FOR THE COOLANT FEED LINE ON THE EXHAUST TURBOCHARGER FOR CYLINDERS 5 TO 8 .
- Refer to IF INSTALLED: INSTALL THE TORSION STRUT ON THE RIGHT, AND ON THE LEFT WHERE REQUIRED .
- Refer to INSTALLING THE CONNECTING SUPPORTS ON THE TUNNEL .
- Refer to INSTALLING LEFT HEAT SHIELD .
- Refer to INSTALLING RIGHT HEAT SHIELD .
- Refer to INSTALLING THE HOLDER FOR THE MONITORING OXYGEN SENSOR ON THE RIGHT .
- Refer to INSTALLING THE HOLDER FOR THE MONITORING OXYGEN SENSOR ON THE LEFT .
- Refer to INSTALLING HEAT SHIELD, TOP .
- Refer to INSTALLING FUEL DELIVERY LINE .
- Refer to INSTALLING RIGHT CLEAN AIR PIPE .
- Refer to INSTALLING LEFT CLEAN AIR PIPE .
- Refer to INSTALLING ENGINE VENTILATION LINE .
- Refer to INSTALLING THE ALTERNATOR .
- Refer to PUTTING ON THE DRIVE BELT .
- Refer to REMOVING SPECIAL TOOL ON BELT TENSIONER .
- Refer to INSTALLING THE LEFT CHARGE AIR LINE .
- Refer to INSTALLING THE RIGHT CHARGE AIR LINE .
- Refer to INSTALLING THE LAMBDA OXYGEN SENSOR AND THE MONITORING OXYGEN SENSOR FOR CYLINDERS 1 TO 4 .
- Refer to INSTALLING THE LAMBDA OXYGEN SENSOR AND THE MONITORING OXYGEN SENSOR FOR CYLINDERS 5 TO 8 .
- Refer to INSTALLING INTAKE FILTER HOUSING .
- Refer to INSTALLING FAN COWL .
- Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLING EQUIPMENT .
- Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT THRUST FIELD .
- Refer to INSTALLING ACOUSTIC COVER .
