Installing all hydraulic valve clearance compensating elements

• Install all the hydraulic valve clearance compensating elements (1) in the direction of arrow.

  Courtesy of BMW OF NORTH AMERICA, INC.

Follow-up Work 

• Refer to INSTALLING ALL ROLLER CAM FOLLOWERS .
• Refer to INSTALLING INTAKE CAMSHAFT .
• Refer to INSTALLING EXHAUST CAMSHAFT .
• Refer to INSTALLING THE INTAKE ADJUSTER .
• Refer to INSTALLING EXHAUST CAMSHAFT ADJUSTER .
• Refer to BLOCKING THE CAMSHAFTS .
• Refer to PRELOAD TIMING CHAIN .
• Refer to TIGHTENING THE VANOS CENTRAL VALVE .
• Refer to DISASSEMBLING ALL SPECIAL TOOLS .
• Refer to CHECKING CAMSHAFT TIMING .
• Refer to INSTALLING THE THERMOSTAT ON THE TRANSMISSION OIL LINES .
• Refer to SECURING THE OIL SUMP ACOUSTIC COVER .
• Refer to CHECKING INSTALLATION POSITION OF ROLLER CAM FOLLOWERS .
• Refer to INSTALLING ALL INTERMEDIATE LEVERS .
• Refer to INSTALLING ALL GATES .
• Refer to CHECKING THE POSITION OF THE INTAKE CAMSHAFT (CYLINDER HEAD REMOVED) .
• Refer to INSTALLING TORSION SPRINGS .
• Refer to INSTALLING SERVOMOTOR FOR THE ECCENTRIC SHAFT .
• Refer to INSTALLING CYLINDER HEAD COVER .
• Refer to INSTALLING BOTH ACTUATORS .
• Refer to PREPARING THE INJECTORS FOR INSTALLATION .
• Refer to INSTALLING INJECTORS .
• Refer to PREPARING FOR THE INSTALLATION OF THE HIGH PRESSURE PUMP .
• Refer to INSTALLING HIGH PRESSURE PUMP .
• Refer to INSTALLING FUEL DELIVERY LINE .
• Refer to INSTALLING THE HIGH-PRESSURE LINE BETWEEN THE HIGH-PRESSURE PUMP AND THE HIGH-PRESSURE RAIL .
• Refer to INSTALLING ALL SPARK PLUGS .
• Refer to INSTALLING THE IGNITION COILS .
• Refer to INSTALLING THE CYLINDER HEAD COVER ACOUSTIC COVER .
• Refer to INSTALLING THE INTAKE PLENUM .
• Refer to INSTALLING THE TANK VENTING VALVE .
• Refer to INSTALLING CONTROL UNIT BRACKET .
• Refer to INSTALLING THE INTEGRATED POWER SUPPLY MODULE (PDM) .
• Refer to INSTALLING THE DME CONTROL UNIT .
• Refer to INSTALLING FRONT ENGINE ENCAPSULATION .
• Refer to INSTALLING AUXILIARY COOLANT PUMP FOR THE EXHAUST TURBOCHARGER .
• Refer to INSTALLING THE ACOUSTIC COVER FOR THE ENGINE AT THE FRONT .
• Refer to CONNECTING THE COOLANT LINE OF HIGH-TEMPERATURE COOLANT CIRCUIT .
• Refer to CONNECTING THE COOLANT LINES FOR THE LOW-TEMPERATURE COOLANT CIRCUIT .
• Refer to INSTALLING CHARGE AIR LINE .
• Refer to INSTALLING CLEAN AIR PIPE .
• Refer to INSTALLING RESONATOR .
• Refer to INSTALLING INTAKE SILENCER HOUSING .
• Refer to INSTALLING CENTER BULKHEAD LOWER SECTION .
• Refer to INSTALLING ACOUSTIC COVER AT REAR .
• Refer to FASTENING HIGH-VOLTAGE CABLES ON THE ELECTRICAL MACHINE ELECTRONICS .
• Refer to INSTALLING RIGHT SEALING FRAME .
• Refer to INSTALLING LEFT SEALING FRAME .
• Refer to INSTALLING THE CENTER BULKHEAD UPPER PART .
• Refer to INSTALLING TENSION STRUT ON SPRING STRUT DOME (LEFT-HAND) , and INSTALLING TENSION STRUT ON SPRING STRUT DOME (RIGHT-HAND) .
• Refer to INSTALLING COWL PANEL COVER .
• Refer to INSTALLING LEFT AND RIGHT WIPER ARM .
• Refer to INSTALLING THE COVER OF THE ENGINE COMPARTMENT ON THE REAR LEFT .
• Refer to INSTALLING THE SEAL FOR THE BONNET .
• Refer to FILLING THE HIGH-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLER DEVICE .
• Refer to FILLING THE LOW-TEMPERATURE COOLING SYSTEM WITH THE VACUUM FILLER DEVICE .
• Refer to BLEEDING THE LOW-TEMPERATURE COOLING SYSTEM .
• Refer to BLEEDING THE HIGH-TEMPERATURE COOLANT CIRCUIT .
• Refer to CHECKING/TOPPING UP OIL LEVEL IN AUTOMATIC TRANSMISSION .
• Refer to CHECKING ENGINE OIL LEVEL .
• Refer to INSTALLING ACOUSTIC COVER .
• Refer to INSTALLING THE REAR STIFFENING PLATE .
• Refer to INSTALLING THE UNDERBODY PROTECTION OF THE STEERING GEAR OR THE FRONT STIFFENING PLATE .
• Refer to INSTALLING THE FRONT UNDERBODY PROTECTION OR FRONT THRUST FIELD .
• Refer to TAKING BONNET OUT OF THE SERVICE POSITION .